Air Oil Separators
All the FILSAN separators used in rotary vane or rotary screw type compressors which manufactured domestically or abroad, are produced by using specially and meticilously designed components of highest quality and standards. For this reason, most of the compressor manufactures and their exclusive distributors have a tendency to use the FILSAN products.

Separators Types
With technical capacity and experience Filsan can manufacture and design higher capacity Separators upon O.E.M’s and customer requests.

Separator Types

Residual Oil content mg/m³     
1 to 3mg/m³

Operating Temperature 120°C

Pressure Drop Bar

Available Nominal Flow Rates

(at 7 bar) (0.7Mpa)

Spin-On Type

+

+

0,25

0,9 to 6,5 m³/min

Standart Type

+

+

0,17

2 to 42m³/min

D-Type

+

+

0,20

3,5 to 58 m³/min


Spin-On Type Separators

The spin-on separators are small in size, their main advantage is that the capacity can be increased by using separate units in line connection. They are designed as easily exchangeable elements not requiring any separator housing. The flow is either from inside to outside or from outside to inside.
The pressure loss is around 0.25 bar at normal operating conditions with 1-3mg/m3 carryover oil content. flow rates are in the range of 0,8 to 6,5 m3/min under 7 bar operation pressure.
The separator canister can withstand to 20 bar pressure and mounted verticaly. There are two systems for the discharge of separated oil. Accumulated oil is removed through a pipe and recirculated. The discharged air should be dry and oil free.

FILSAN Ref.

OD1

ID1

H1

Flow Rate (m³/min)

FS110/S

76

M 22X1.5

127

1.0

FS110/S-1

76

M 22X1.5

142

1.0

FS111/S

93

M 24X1.5

212

2.0

FS111/S-1

93

M 24X1.5

172

1.7

FS113/S

136

M 39X1.5

302

5.5

FS114/S

136

M 39X1.5

350

6.5

FS115/S

108

M 32X1.5

260

4.0

FS120/S

108

1"3/8-16UN

261

4.0

FS130/S

93

M 25X1,5

212

2.0

FS132/S

136

M 40X1,5

350

6,5

FS134/S

93

M 25X1,25-L

212

2.0

FS136/S

108

M 32X1,5-L

261

4.0

FS140/S

136

M41X1.5

302

5,5

FS141/S

108

M 32X1.5

112

2.0

FS142/S

136

M 40X1,5-L

302

5.5

FS143/S

136

M 40X1,5

177

3.0

FS144/S

136

M 37X1,5

302

5.5

FS146/S

136

M 40X1,75

302

5.5

FS149/S

136

M 42X1,5

302

5.5


* Specially designed and higher capacity separators are available.
* Please check our cross reference list for more different types and for part references.



More Information

Standart Type Separators

Air oil separators remove compressor lubricant from the compressed air stream. During normal operation, the compressor lubricant is returned to the oil sump and the compressed air continues to the air receiver. A typical oil separator reduces the lubricant entrained in the compressed air to 0,3ppm. Under normal operating conditions an oil separators service life is 4,000 to 6,000 operating hours (when the flow resistance reaches 1 bar (0.1MPa).

FILSAN

REF.

Flow

rate

(m³/min)

d1

(mm)

d2

(mm)

d3

(mm)

d4

(mm)

d5

(Ø)(mm)

d6

(mm)

h1

(mm)

h2

(mm)

 FS 593

9

220

165

-

274

-

-

435

12

 FS 540

12

275

220

-

328

-

-

450

12

 FS 541

14

300

245

-

355

-

-

500

12

 FS 590

17

300

245

-

355

-

-

600

12

 FS 542

19

300

245

-

355

-

-

660

12

 FS 755

20

275

220

-

324

-

-

750

12

 FS 543

24

300

245

-

355

-

-

820

12

 FS 963/S

29

300

230

 

355

 

 

1000

12


* Specially designed and higher capacity separators are available.



More Information

D-Type Separators

These type separators, as shown in Figure, are so designed that they fit the smaller separator housings without reducing the capacity or operating performance of the compressor. When compared to a conventional separator of the same dimensions, these separators have double or even triple capacity. The mentioned increase in capacity is simply achieved by using higher number of wraps in the separators.

FILSAN

REF.

Flow rate

(m³/min)

d1

(mm)

d2

(mm)

d3

(mm)

d4

(mm)

d5

(Ø)(mm)

d6

(mm)

h1

(mm)

h2

(mm)

FS 769/D

4,5

135

75

-

170

-

-

200

-

FS 840/D

20

275

209

-

328

-

-

400

-

FS 915/D

33,5

300

220

-

355

-

-

600

-

FS 877/D

39

300

220

-

355

-

-

700

-

SPECIAL

53

300

230

-

355

-

-

860

-

FS 963/D

58

300

230

-

355

-

-

1000

-


* Specially designed and higher capacity separators are available.

Maintenance advice and Service life
•Pressure Drop at Load: 2-3 psi (150-200mbars)/100psi (7 bar)
•Collapse Strength: 50 psi (3.5 bars) minimum
•Oil Carry Over Rate: 1-3 ppm / 1-3 mg/m³
•Operating Temperature: 180°-250° F / 82°-121° C
•Materials: Urethane (or epoxy), galvanized steel and various high- performance Microglass fiber media configurations.

If Filsan’s Separators are Installed correctly and maintained properly, expected life is several thousand (up to 4000 ) hours. Air Oil Separators must be replaced if the flow resistane reaches 1 bar (0,1 MPa). This will vary considerably depending on maintenance, application, installation, usage and environmental conditions. (i.e. dust, humidity, smoke, pollution, etc.) Air intake filter, oil filter and coolant quality can have an impact on the separator service life. Filsan offers unique high efficiency air intake filters made of nano glass fibers to stop short service life problems on separators. Filsan separator construction and high-performance Microglass fiber media provides additional protection and maximum separator life.

•Quality Control: Filsan separators are 100% inspected for structural
integrity and conductivity.



More Information

CONTACT US

Аddress

Çerkeşli O.S.B. Mah. İmes O.S.B, İmes Bulvarı, 1.Cad. No:26, Dilovası - KOCAELİ/TURKEY

Тelephone

+90 (0262) 722 93 90
+90 (0262) 722 9391

E Mail

info@filsan.com.tr
sales@filsan.com.tr




Copyright © 2022 FILSAN Filtre ve İnş. San. Tic. Ltd. Şti.

FILSAN FILTER

Filsan Filter founded in 1980. The company has started manufacturing filter products on 1980 for local and foreign automobile industry and diversified its product range to Air Filters, Oil Filters, Fuel Filters and Hydraulic Filters for heavy duty vehicles, industrial machines and construction machinery.
Click to Details...

Air Oil Separators
All the FILSAN separators used in rotary vane or rotary screw type compressors which manufactured domestically or abroad, are produced by using specially and meticilously designed components of highest quality and standards. For this reason, most of the compressor manufactures and their exclusive distributors have a tendency to use the FILSAN products.

Separators Types
With technical capacity and experience Filsan can manufacture and design higher capacity Separators upon O.E.M’s and customer requests.

Separator Types

Residual Oil content mg/m³     
1 to 3mg/m³

Operating Temperature 120°C

Pressure Drop Bar

Available Nominal Flow Rates

(at 7 bar) (0.7Mpa)

Spin-On Type

+

+

0,25

0,9 to 6,5 m³/min

Standart Type

+

+

0,17

2 to 42m³/min

D-Type

+

+

0,20

3,5 to 58 m³/min



Spin-On Type Separators

The spin-on separators are small in size, their main advantage is that the capacity can be increased by using separate units in line connection. They are designed as easily exchangeable elements not requiring any separator housing. The flow is either from inside to outside or from outside to inside.
The pressure loss is around 0.25 bar at normal operating conditions with 1-3mg/m3 carryover oil content. flow rates are in the range of 0,8 to 6,5 m3/min under 7 bar operation pressure.
The separator canister can withstand to 20 bar pressure and mounted verticaly. There are two systems for the discharge of separated oil. Accumulated oil is removed through a pipe and recirculated. The discharged air should be dry and oil free.

FILSAN Ref.

OD1

ID1

H1

Flow Rate (m³/min)

FS110/S

76

M 22X1.5

127

1.0

FS110/S-1

76

M 22X1.5

142

1.0

FS111/S

93

M 24X1.5

212

2.0

FS111/S-1

93

M 24X1.5

172

1.7

FS113/S

136

M 39X1.5